The mandatory national standard for lamps approved by the State Bureau of Quality and Technical Supervision was implemented on January 1, 2009. The standard stipulates that Class 0 lamps with the lowest safety level will be gradually withdrawn from the market. In the nearly two months after the implementation of the standard, the author visited the lighting market in Taiyuan City and found that the current household lamps are still mostly Class 0 lamps. Most consumers did not notice the safety level when purchasing lamps. Relevant data show that the lamps can be divided into Class 0, Class I, Class II and Class III according to the category of protection against electric shock. Among them, Class 0 lamps have the worst safety, and the insulating materials only rely on a layer wrapped on the wire. Thin insulation and no grounding plug. In the newly implemented national standards, the original Class 0 lamps were officially deleted and gradually withdrawn from the market. However, the author learned from several lighting markets in Taiyuan City that most of the household lamps, floor lamps, and craft lamps currently distributed in the market are still Class 0 lamps. A lighting dealer introduction: Identifying 0 types of lamps mainly depends on the wrapping of their wires. These products generally have only one layer of rubber. When peeling off the rubber, you can see the copper wire inside; the plug of the wire is double-ended and has no grounding port. . Such simple insulation measures make some lamps (table lamps, floor lamps) have aging or damage of the insulation during use, which is easy to cause electric shock to the user, and the safety hazard is great. Compared with Class 0 lamps, Class I lamps, in addition to the basic insulation, also connect the easily accessible conductive parts to the grounding device, which is much safer, and the safety performance of Class II and Class III is higher. The author saw in several lighting stores in a decorative market in Xinghua Street that the wires of some lamps are mostly slender, and the plugs are double-ended and have no grounding end. When the author asked the owner about the security level of a desk lamp, the owner was very confused and asked: "The lights are still classified. I have never heard of it." The dealers don't know the standard, and the consumers don't know the standard. In the small appliance area of ​​a shopping mall, the author asked several citizens who were choosing the lamp to know whether they understood the anti-shock protection category of household lamps. The respondents looked blank. According to industry sources, the most common household lamps in Taiyuan currently have table lamps, floor lamps, etc., of which 0 types of lamps account for more than 70%. Industry and quality inspectors said that the Class 0 lamps that have been produced before the implementation of the new standards can still be distributed in the market, but remind everyone to purchase high-quality lamps to prevent accidents caused by the use of lamps with low safety performance. Editor: China Lighting Network Feng Yaoyuan    5.08MM Wire To Board Connectors
5.08MM Wire To Board Connectors
5.08 mm Wire to Board connectors are avialable in different terminations and sizes intended for use on a variety of applications. These connectors provide power and signal with different body styles, termination options, and centerlines. To find the wire to board set required, click on the appropriate sub section below.
5.08mm Wire To Board Connectors Type
5.08mm Terminal
5.08mm Wire To Board Connectors Advantages
5.08 mm Wire To Board Connectors Application
5.08MM Wire To Board Connectors ShenZhen Antenk Electronics Co,Ltd , https://www.atkconnectors.com
5.08mm Housing
Pitch 5.08mm Wafer Right Angle&SMT Type
5.08mm Wafer Straight Type
5.08mm Wafer SMT Type
5.08mm Wafer Right Angle Type
5.08mm Wafer Single Row Straight Type
5.08mm Wafer Single Row SMT Type
5.08mm Wafer Double Row Straight Type
5.08mm Wafer Double Row SMT Type
5.08mm Wafer Double Right Angle Type
5.08mm Wafer Double Right Angle&SMT Type
Small electronics with high current requirements
One of the strongest advantage of the Micro Fit series is its applicability in delivering the high current requirement in electronics with supplying high power.
Safe and Reliable
ensure safety, system protection and performance with its bonded metallic conduits and multiple grounding points preventing fire hazards, component damage, overheating and possible electrocution.
ROHS Compliant
The product does not contain restricted chemicals in concentrations not complying with ROHS standards. Thus, for its components, the products can be worked upon at high temperatures required by lead-free soldering.
Motherboard Connectors
The Motherboard of a computer holds together many of the crucial components such as the central processing unit (CPU), memory and connectors for input and output devices. Microfit connectors ensure high performance electronic system in quality motherboards.
You can easily find Scondar`s Microfit in most ITX Motherboards, in which its functionality is best described for solid performance in a small footprint, and low power consumption (less than 100 Watts).
Printer Connectors
The 5.08mm Microfit can also be seen in most printers
Automotive PC Connectors
Smart, high power automotive PC power supply garners its capabilities from quality Microfit connectors, designed for general purpose battery powered applications. These are manufactured to provide power and to control the motherboards' switch based on ignition status.
Solar Panels
Microfit can also be commonly found in a solar array. A solar array is connected to each other, and to inverters through connectors to produce a successful flow of electricity.